| View previous topic :: View next topic |
| Author |
Message |
Graflite
Joined: 08 Nov 2001
Posts: 103
Location: Southeast US
|
 Posted: Wed Dec 05, 2001 3:44 am Post subject: |
 |
|
I was curious if the Graflex Quick Release Clamps used on the Graflite flash handles (both the older bulb flash battery case and the newer Strobe 250, etc.) would fit well on the tube handle of the Sunpak 611 flashgun.
I can't locate locally a 611 to find out for sure and would greatly appreciate hearing from someone who has used the clamps with the 611.
Thanks for any information that you might have. |
|
| Back to top |
|
 |
RichS
Joined: 18 Oct 2001
Posts: 1468
Location: South of Rochester, NY
|
| Posted: Thu Dec 06, 2001 8:15 pm Post subject: |
|
|
Since noone else has answered deffinitively yet...
As far as I know, the 611 has a larger diameter. I have the 622 and it's 1 11/16. The Graphic clamps are 1 1/2. There's absolutely no way to 'stretch' the clamps around the larger handle. I have bought an extra set and intend to cut off the 'strap' part of the clamps and replace it with something like an automotive hose clamp, screwed to the sides of the Graphic clamp housing. This will allow it to fit the 622 and any other semi-round handle flash. Haven't quite done it yet due to other priorities... If someone can measure the 611, or check sunpaks web site (although I don't think the info is there), you could know for sure...
Rich...
|
|
| Back to top |
|
|
Graflite
Joined: 08 Nov 2001
Posts: 103
Location: Southeast US
|
| Posted: Sat Dec 08, 2001 12:07 am Post subject: |
|
|
Thanks to RichS for the info on the diameter of the Sunpak flash handles, I had hoped to keep using the Graflex clamps & bracket system with an auto flashgun such as the 611 and use it with my 4 x 5 Crown Graphic Special.
I guess I'll stick with my Graflite Strobe 250 for now, I just ordered a 510 VDC Ni-Cad battery that will fit in the Graflite Strobe 250 battery pack, and the charger for it.
I'm still working on the hybrid strobe flash inside a #2773 flash handle using a 7 inch reflector, the only downside is having to carry a battery pack on the belt, but it sure beats flashbulbs and doesn't look too out of place attached to the Crown.
Again thank to RichS for the helpful info. |
|
| Back to top |
|
|
GR
Joined: 16 Feb 2002
Posts: 1
Location: Oregon
|
| Posted: Sat Feb 16, 2002 11:38 pm Post subject: |
|
|
I've adapted the clamps to a Sunpak 544 potatoe masher flash. ( I believe the handle's diameter is the same as on a 611) It required brazing a spacer in the clamp's band and lots of intricate filing of the square prong end because the radius changed from the increased diameter. Amazing how well made those clamps were. Solid brass with some extremely durable hard as nails finish. I'll never do it again!
_________________
Regards, Greg |
|
| Back to top |
|
|
RichS
Joined: 18 Oct 2001
Posts: 1468
Location: South of Rochester, NY
|
| Posted: Sun Feb 17, 2002 5:19 am Post subject: |
|
|
| Quote: |
On 2002-02-16 15:38, GR wrote:
I've adapted the clamps to a Sunpak 544 potatoe masher flash. ( I believe the handle's diameter is the same as on a 611) It required brazing a spacer in the clamp's band and lots of intricate filing of the square prong end because the radius changed from the increased diameter. Amazing how well made those clamps were. Solid brass with some extremely durable hard as nails finish. I'll never do it again!
|
I've done almost the same thing for my 622. I was in too much of a rush to do the brazing though. So I cut a slot in each side the the clamps and used a heavy nylon wire tie through the slots and around the flash handle. Not adjustable or removable, but works just fine for now. I hope to 'fill the gap' with some brass work some day soon since I just snipped the strap in the middle to allow the filling at a later time.
I was very surprised too with their quality. The 'filing' is made a whole lot easier with a Dremel & burr bit. Too easy unfortunately as one quick slip leaves a good gouge  But it does beat the hand file method. It's a shame they didn't keep the 1 1/2 inch 'standard'...
|
|
| Back to top |
|
|
jdman
Joined: 13 May 2001
Posts: 302
Location: Midwest
|
| Posted: Sun Feb 17, 2002 5:39 am Post subject: |
|
|
| A Sunpack or Vivitar 283 mounted on top of a 2773 Graflite, along with a solenoid makes for real nice setup. I took the rubber cap off an old graflex strobe and mounted a shoe to it and slid it over the top of the 2773. Also it makes a nice Handhold. Nothing is as slick as a solenoid for shutter release. Russ |
|
| Back to top |
|
|
Texas Ed
Joined: 02 Oct 2001
Posts: 21
|
| Posted: Wed Mar 06, 2002 1:58 pm Post subject: |
|
|
| Quote: |
On 2001-12-07 16:07, Graflite wrote:
Thanks to RichS for the info on the diameter of the Sunpak flash handles, I had hoped to keep using the Graflex clamps & bracket system with an auto flashgun such as the 611 and use it with my 4 x 5 Crown Graphic Special.
I guess I'll stick with my Graflite Strobe 250 for now, I just ordered a 510 VDC Ni-Cad battery that will fit in the Graflite Strobe 250 battery pack, and the charger for it.
snip
|
Was that the SunPak NC510 battery? How did the NiCad work out? I've been planning on using one with a Strobonar 880 Pressmaster pack, just haven't gotten a "round tuit". Seems like it should work just fine, though the SunPak NC510 has a couple of extra contacts. Anyone know for sure what the extra contacts are for?
Thanks,
Ed |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
